Search Results

The paper describes a universally structured simulation platform which is used for the analysis and prediction of combustion in compression ignition (CI) engines. The models are on a zero-dimensional crank angle resolved basis as commonly used for engine cycle simulations. This platform represents a kind of thermodynamic framework which can be linked to single and multi zone combustion models. It is mainly used as work environment for the development and testing of new models which thereafter are implemented to other codes. One recent development task focused on a multi zone combustion model which corresponds to the approach of Hiroyasu. This model was taken from literature, extended with additional features described in this paper, and implemented into the thermodynamic simulation platform.

The target of the investigation is the particular influence of a fuel injection system and its components as a noise source in automotive engines. The applied methodology is demonstrated on an automotive Inline 4-cylinder Diesel engine using a common rail system. This methodology is targeted as an extension of a typical standard acoustic simulation approach for combustion engines. Such approaches basically use multi-body dynamic simulation with interacting FEM based flexible structures, where the main excitation crank train, timing drive, valve train system and piston secondary motion are considered. Within the extended approach the noise excitation of the hydraulic and mechanical parts of the entire fuel system is calculated and subsequently considered within the multi-body dynamic simulation for acoustic evaluation of structural vibrations.

Mechanical variable valve systems are being increasingly used for modern combustion engines. It is typical for such systems that the cam and valve are connected via intermediate levers. Different maximum valve lifts and duration can be achieved with the same cam profile. The intermediate levers increase the system inertia and reduce the overall stiffness. Such systems offer more flexibility, but it is more complex to create optimal design compared to the conventional systems. In this paper a new kinematic design methodology for a CVVL (Continuously Variable Valve Lift) system is presented. Additionally, dynamic analysis of the valve train system is performed. The investigated valve train is completely developed and patented by OEM. The main characteristic of the CVVL system is a set of intermediate levers between the cam and the finger follower like ( 1 , 2 ). One cam drives two intake valves over a set of levers.

According to the ISO 16183 [1] protocol for heavy-duty diesel engines, particulate matter can be determined using a partial flow dilution system (PFDS). In order to control a PFDS, it is necessary to know the exact exhaust gas mass flow rate at the sample probe of the system at any given time. For the purpose of operating a PFDS with online control, a transformation time for the entire system (exhaust mass flow determination and partial flow adjustment) of equal or less than 300 ms is specified. In order to minimize the dynamic requirements for the PFDS a fast determination of the exhaust flow rate is necessary, which can be achieved most easily by using the intake flows (air + fuel flow) into the engine. This paper reports on the development and testing of an intake flow based model for calculating real time exhaust flow rate that accounts for the influence of the filling and emptying of the manifolds of a turbocharged diesel engine during dynamic operation.

Recent turbocharged Gasoline engines based on MPFI offer excellent power output and high nominal torque, however, also some disadvantages. The most significant restrictions of TC-engines - like poor fuel economy, limited emission capability and delayed transient response (turbo lag) - can be improved dramatically by a refined GDI application. The synergy effects of GDI, which are also partly used at naturally aspirated engines, are even more significant with turbocharging. The low emission capability of GDI enables turbocharged SULEV concepts within moderate cost of the emission / aftertreatment system. The outstanding low-end-torque, the high specific power and torque output of refined GDI-Turbo concepts enable high fuel efficiency combined with excellent fun to drive. Thus such GDI-Turbo concepts will become the most attractive technology to fulfill highest fuel economy-, emission- and performance requirements simultaneously.

The CMS system commissioned by EPA and built by AVL, is a “start from a clean sheet of paper” approach to a full flow sampling system for aerosol matter from engine exhaust. The challenge of measuring 2007 level post DPF type particulate matter and polyaromatic hydrocarbons led to this re-thinking of sampler design. Previously used CVS designs had evolved to include elements that were not ideally suited for scaling up to large flow rates, and had mixing tunnels that were less than ideal for the sampling of complicated aerosols. The solution presented in this paper used ultrasonic time-of-flight flowmeters in place of the usual Venturi flow tubes, reducing the size and cost of air handling components. Acoustically designed dampeners were used to reduce pulsation disturbances to the flow measurement.

When exhaust emissions from a vehicle are measured, a flow rate is needed in addition to pollutant concentrations in order to calculate the mass emitted. The highly unsteady flow from an internal combustion engine presents measurement challenges to exhaust flowmeters, especially at idle. Mass measurement methods used in the past have gotten around this problem by a variable dilution scheme (CVS) that measures a different, more favorable flow, but reduces and can contaminate exhaust gas concentration levels. The flow measurement system described here makes possible a more accurate measure of the vehicle exhaust flow by means of a number of design features. This improves considerably the cost effectiveness and accuracy of emissions measurement techniques such as the Bag-Minidiluter sampling system and raw modal analysis.

Partial flow sampling methods in emissions testing are interesting and preferred because of their lower cost, smaller size and applicability to engines of all sizes. However the agreement of the results obtained with instruments based on this method to those obtained with the traditional, large tunnel full flow sampling systems needs to be achieved, and the factors of construction that influence this agreement must be understood. These issues have received more attention lately in connection with ISO and WHDC standardization efforts underway to achieve a world-wide harmony in the sampling methods for heavy duty diesel engines, and with the introduction of similar Bag-minidiluter techniques into light duty SULEV gaseous pollutant measurement. This paper presents the theory and practice of a partial flow probe and tunnel design that addresses and minimizes the undesirable effects of the necessary differences between the two sampling methods.

Light duty diesel vehicles continue to win recognition and market shares in Europe due to their convincing economy, reliability and driveability features. The diesel boom finds a fresh rationale in the CO2 emission legislation to come, however, the competitiveness of diesel cars may be impaired in future in consequence of the progression of the exhaust emission legislation and its impact on vehicle cost. This paper reviews the technologies currently pursued on the side of the engine and its subsystems, as well as the exhaust gas aftertreatment concepts required to satisfy the European legislation. An integral system approach is suggested, aiming at an optimum match of vehicle design parameters, transmission gear and the engine including aftertreatment elements and control.

Increasing requirements for the result quality of exhaust emission analyzers and state of the art analyzer technology require a new point of view regarding measuring range definitions and linearization procedures. To make best use of the power of this analyzer technology, linearization procedures need reconsideration. In certification laboratories, legislation defines the procedures to linearize an exhaust emission analyzer more or less stringently. On the other hand, on testbeds for development purposes there are many possibilities for making use of today's improved analyzers. However, procedures are often used in development labs that are very similar to those mentioned in the legislation. For some measurement purposes it is necessary to leave these procedures regarding measuring ranges and their specifications behind. The exhaust gas analyzing system has to provide consistent result quality during the whole test procedure.

The next generation of automotive engines has to meet 2004 emission limits, ideally with improved fuel economy and with noise emission which is at least 3 dBA below the current status. Using both simulation and experimental analysis these challenging requirements can only be fulfilled by clearly defining all key steps in NVH development and by applying suitable technological methods. The development procedure discussed in this paper is characterised by several aspects: two stage prediction procedure fully integrated in the design process, combustion development with a definite focus on noise, a closed loop between simulation and test bed development and consideration of noise in the calibration of engine and drivetrain management systems. Apart from meeting target noise levels, noise quality is the reference parameter which is continuously evaluated by means of the AVL Annoyance Index.

Due to increasing complexity of engine electronic systems, there is a demand to handle the often more than 10,000 calibration data automatically. Establishing optimized start of injection and EGR tables of a TC DI Diesel engine by conventional methods takes about two weeks of intensive calibration work. By automatic map calibration, this task can be handled in less than 20 hours automatically, with no staff required during optimization. The benefits of automatic calibration therefore are reduced costs and faster response to any changes in parameters, even with complex multidimensional engine calibration problems. The paper describes the optimization method as well as the experimental work on the test stand that produces the results.